vapeciga.com
Initiate
- Joined
- Aug 30, 2019
- Messages
- 43
Next, there is the problem of how to wear cotton, which is ignored by many users, because everyone will think psychologically that they have used the e-cigarette for so long, how can they wear bad cotton? Actually not.
Smok mag 225w is a best TC mod kit, and it is worth purchasing.
Many users will encounter that even if the power is set at a low level, they will enter the temperature protection mode 1 second after ignition, which makes them puzzled but unable to find the reason. In fact, the source of this problem is basically the penetration of cotton, which is not obvious in the traditional pressure regulating mainframe on the performance of the temperature control mainframe is very prominent.
When cutting the cotton as a Ni200 coil, try to cut the cotton according to the principle of "better thick than thin" on the premise that it will not be too thick to affect the guide speed of the cotton in the atomizer. Only when the cotton is fully wrapped by the Ni200 coil can the main engine correctly sense the true operating temperature of the Ni200 coil, cotton and smoke oil in the atomization chamber. Otherwise, if the cotton in the coil are too poor, in the heat of the moment, between the coil and cotton oil smoke was instantly blown up, after fully contact area of lost and cotton, also loses the perception of oil smoke temperature, the result and dry coil, that is the reason why many users frequently encountered temperature protection.
Finally, is the choice of atomizer, a large resistance or resistance atomizer is definitely not suitable for temperature control, like a measured resistance to temperature control host cannot realize the temperature control of reason, steam website has more internal resistance of the atomizer with the above the mainstream market internal resistance test, for details, please visit: "the five common atomizer resistance test.
KFLP made a comeback after the flash in the pan of KF4, demonstrating the importance of internal resistance and stability of a atomizer when used for temperature control. Interested users can do such an experiment: drop smoke oil into the positive and negative screw holes of the KFLP, and then make the coil and wear the cotton for use. In this case, the stability of the KFLP is much worse than under normal circumstances. This indicates that a KFLP atomizer with a minimal structure will produce inaccurate internal resistance even if it accumulates oil where it should not. Consider how poorly a atomizer with a complex base structure that condensates and accumulates oil everywhere after use is suitable for temperature control.
Smok mag 225w is a best TC mod kit, and it is worth purchasing.
Many users will encounter that even if the power is set at a low level, they will enter the temperature protection mode 1 second after ignition, which makes them puzzled but unable to find the reason. In fact, the source of this problem is basically the penetration of cotton, which is not obvious in the traditional pressure regulating mainframe on the performance of the temperature control mainframe is very prominent.
When cutting the cotton as a Ni200 coil, try to cut the cotton according to the principle of "better thick than thin" on the premise that it will not be too thick to affect the guide speed of the cotton in the atomizer. Only when the cotton is fully wrapped by the Ni200 coil can the main engine correctly sense the true operating temperature of the Ni200 coil, cotton and smoke oil in the atomization chamber. Otherwise, if the cotton in the coil are too poor, in the heat of the moment, between the coil and cotton oil smoke was instantly blown up, after fully contact area of lost and cotton, also loses the perception of oil smoke temperature, the result and dry coil, that is the reason why many users frequently encountered temperature protection.
Finally, is the choice of atomizer, a large resistance or resistance atomizer is definitely not suitable for temperature control, like a measured resistance to temperature control host cannot realize the temperature control of reason, steam website has more internal resistance of the atomizer with the above the mainstream market internal resistance test, for details, please visit: "the five common atomizer resistance test.
KFLP made a comeback after the flash in the pan of KF4, demonstrating the importance of internal resistance and stability of a atomizer when used for temperature control. Interested users can do such an experiment: drop smoke oil into the positive and negative screw holes of the KFLP, and then make the coil and wear the cotton for use. In this case, the stability of the KFLP is much worse than under normal circumstances. This indicates that a KFLP atomizer with a minimal structure will produce inaccurate internal resistance even if it accumulates oil where it should not. Consider how poorly a atomizer with a complex base structure that condensates and accumulates oil everywhere after use is suitable for temperature control.
