Juice Shop
Postman
- Joined
- Aug 2, 2012
- Messages
- 459
View attachment 972
this is what i as told:
Zmax User Settings
Features:
Zmax is a new intelligent e cig Mod,not only you could adjust the voltage,but also you could adjust the wattage.It could work with one 18650 battery and also two 18350 batteries with extra longer buttom cap.It's a constant voltage and constant wattage new VV Mod.
Zmax can be adjusted from 3.0-6.0V volts in 0.1 volt increments.
Built-in three digit display allows you to visually adjust your voltage and wattage.
Zmax could fit one battery 18650 or add holds two specially designed 18350 High Power Batteries,and reverse connect protection.
ZMax is made of brass or stainless.
Zmax is with 510 and EGO thread.
With a maximum output of 15 watts.
ZMax can be adjusted power from 3.0 --15 W in 0.5 watts increments.
ZMax PCB allows 4 Amperage output limit.
ZMax buttom never get stucked even theres a 360°turnning around
In this guide we will explain how to change settings.It's easy and funny!
The menu is arranged in the following order:
1.Uu --- Voltage up
2.Ud --- Voltage down
3.So --- Standby on/off
4.Uc --- Voltage check of battery
5.Ds --- Display change
Do --- Display cartomizer/atomizer output voltage
Du --- Display battery output voltage
DR---Display cartomizer/atomizer resistance
6.Lo --- Led light on/off
7.Up --- Voltage power
Po --- Constant power operation
Uo --- Constant voltage operation
1.Uu--Voltage Adjust Up
Zmax is a smart microprocessor controlled electronic cigarette,that uses the lastest technology to allow you to set a range of voltages.
With its built-in three digital display there are no analog dials or potentiometers to wear out.There's no way to accidentally reset the
voltage and you can make changes within seconds.
Zmax allows you to digitally dial in your favorite voltages on its mini display.
You can adjust the voltage from 3.0 to 6.0 using the built in user interface
Note --- The higher the voltage,the hotter the heating element will get!
It always starts at a low voltage setting.Please increase the power until you are satisfied with the vapor production.
2.Ud--Voltage Adjust Down
In this mode you can adjust the power down to save button clicks.
It's got the same functionality of the power up except each time you press the button it will lower the power.
If you make a mistake,just press the button 4 times in a row and you will be able to make another change.
3.So--Standby on/off
In Off of the"Standby mode" the Zmax will not activate the atomizer/cartomizer when the button is pressed and you will not be able to change any of the settings.
This mode is good for when you want to store the Zmax in your pocket or bag and don't want it to accidentally turn on the atomizer/cartomizer.
Once you have turned the device off,you can turn it back on by pressing the button 5 times to access this menu function again or you can simply remove the battery and re-insert to turn the Zmax back on.
4.Uc--Voltage check of battery
In this mode you can check the level of your battery in volts.
5.Ds--Display change
In this mode the Zmax will read and display your atomizer/cartomizer ohms measurement,your battery voltage and your atomizer/cartomizer output voltage.
This feature is useful if you want to check what type of atomizer/cartomizer you have installed,and what atomizer/cartomizer output voltage is when the battery is working.
It's normal for your atomizer/cartomizer to activate at a very low voltage while in Ohms mode.This allows the Zmax to check the resistance.
6.Lo--Display on/off
Display ON --- In this mode,the Zmax Display could read the atomizer/cartomizer ohms measurement,the battery voltage and the atomizer/cartomizer output
voltage when this mode is turned ON
Display OFF --- In this mode,the Zmax Display couldn't read the atomizer/cartomizer ohms measurement,the battery voltage and the atomizer/cartomizer output
voltage when this mode is turned OFF
7.Up--Voltage power
In this mode you can adjust the power down to save button clicks.
It's got the same functionality of the power up except each time you press the button it will lower the power.
Error Codes
LOR---Lower resistance indication;If the resistance is below 1.2ohm,the display will show "Low Load".
LOU---Lower voltage indication.If one 18650 battery voltage is below 3.4V or 2 18350 batteries Superposition voltage is below 6.4v,the display will show"Low Voltage".
WSC---Short circuit indication.If cartomizer/atomizer output port short-circuit,the display will show"Warning Short Circuit".
this is what i as told:
Zmax User Settings
Features:
Zmax is a new intelligent e cig Mod,not only you could adjust the voltage,but also you could adjust the wattage.It could work with one 18650 battery and also two 18350 batteries with extra longer buttom cap.It's a constant voltage and constant wattage new VV Mod.
Zmax can be adjusted from 3.0-6.0V volts in 0.1 volt increments.
Built-in three digit display allows you to visually adjust your voltage and wattage.
Zmax could fit one battery 18650 or add holds two specially designed 18350 High Power Batteries,and reverse connect protection.
ZMax is made of brass or stainless.
Zmax is with 510 and EGO thread.
With a maximum output of 15 watts.
ZMax can be adjusted power from 3.0 --15 W in 0.5 watts increments.
ZMax PCB allows 4 Amperage output limit.
ZMax buttom never get stucked even theres a 360°turnning around
In this guide we will explain how to change settings.It's easy and funny!
The menu is arranged in the following order:
1.Uu --- Voltage up
2.Ud --- Voltage down
3.So --- Standby on/off
4.Uc --- Voltage check of battery
5.Ds --- Display change
Do --- Display cartomizer/atomizer output voltage
Du --- Display battery output voltage
DR---Display cartomizer/atomizer resistance
6.Lo --- Led light on/off
7.Up --- Voltage power
Po --- Constant power operation
Uo --- Constant voltage operation
1.Uu--Voltage Adjust Up
Zmax is a smart microprocessor controlled electronic cigarette,that uses the lastest technology to allow you to set a range of voltages.
With its built-in three digital display there are no analog dials or potentiometers to wear out.There's no way to accidentally reset the
voltage and you can make changes within seconds.
Zmax allows you to digitally dial in your favorite voltages on its mini display.
You can adjust the voltage from 3.0 to 6.0 using the built in user interface
Note --- The higher the voltage,the hotter the heating element will get!
It always starts at a low voltage setting.Please increase the power until you are satisfied with the vapor production.
2.Ud--Voltage Adjust Down
In this mode you can adjust the power down to save button clicks.
It's got the same functionality of the power up except each time you press the button it will lower the power.
If you make a mistake,just press the button 4 times in a row and you will be able to make another change.
3.So--Standby on/off
In Off of the"Standby mode" the Zmax will not activate the atomizer/cartomizer when the button is pressed and you will not be able to change any of the settings.
This mode is good for when you want to store the Zmax in your pocket or bag and don't want it to accidentally turn on the atomizer/cartomizer.
Once you have turned the device off,you can turn it back on by pressing the button 5 times to access this menu function again or you can simply remove the battery and re-insert to turn the Zmax back on.
4.Uc--Voltage check of battery
In this mode you can check the level of your battery in volts.
5.Ds--Display change
In this mode the Zmax will read and display your atomizer/cartomizer ohms measurement,your battery voltage and your atomizer/cartomizer output voltage.
This feature is useful if you want to check what type of atomizer/cartomizer you have installed,and what atomizer/cartomizer output voltage is when the battery is working.
It's normal for your atomizer/cartomizer to activate at a very low voltage while in Ohms mode.This allows the Zmax to check the resistance.
6.Lo--Display on/off
Display ON --- In this mode,the Zmax Display could read the atomizer/cartomizer ohms measurement,the battery voltage and the atomizer/cartomizer output
voltage when this mode is turned ON
Display OFF --- In this mode,the Zmax Display couldn't read the atomizer/cartomizer ohms measurement,the battery voltage and the atomizer/cartomizer output
voltage when this mode is turned OFF
7.Up--Voltage power
In this mode you can adjust the power down to save button clicks.
It's got the same functionality of the power up except each time you press the button it will lower the power.
Error Codes
LOR---Lower resistance indication;If the resistance is below 1.2ohm,the display will show "Low Load".
LOU---Lower voltage indication.If one 18650 battery voltage is below 3.4V or 2 18350 batteries Superposition voltage is below 6.4v,the display will show"Low Voltage".
WSC---Short circuit indication.If cartomizer/atomizer output port short-circuit,the display will show"Warning Short Circuit".
