POTV - Your vaping community

Wanting to join the rest of our members? Why not sign up today!

Register

SS316 Clapton on Ammit

Discussion in 'Good Builds' started by trickywoo, Jan 13, 2017.

  1. trickywoo

    trickywoo Initiate

    Joined:
    May 10, 2015
    Messages:
    48
    Likes Received:
    49
    This is my current temp control set up, 7 wrap of 26 wrapped in 32 SS316L.
    Internal Diameter is 2.5mm and is reading as 0.51 ohms.

    I normally vape it at around 215 Celsius but I highly doubt the coil gets that warm with the airflow in this thing!

    Oh and the wire was bought, I do not have the patience to Clapton my own wire!

    [​IMG]
     
    • Like Like x 3
  2. The Electronic Cigarette Company
  3. junglist

    junglist Administrator Staff Member

    Joined:
    Aug 14, 2012
    Messages:
    7,033
    Likes Received:
    8,273
    Thanks for adding! I like the look of the ammit, think I might have to get one. Airflow looks superb :D
     
  4. trickywoo

    trickywoo Initiate

    Joined:
    May 10, 2015
    Messages:
    48
    Likes Received:
    49
    I have quite an odd relationship with it at the moment, I'll use it for most of the day and then suddenly I'll feel like the flavour isn't quite there, but trying another tank proves me very wrong! It's great overall, even if the juice flow is fairly restricted (I'm sticking to 70/30 juices with it). Would definitely recommend it though!

    Side note, it's worth keeping the afc at around the halfway mark for a decent draw.
     
  5. We Vape
  6. Major Hazzard

    Major Hazzard Achiever

    Joined:
    Jan 27, 2014
    Messages:
    1,361
    Likes Received:
    643
    Thaks for posting this.. I cannot seem to get the Ammit working properly..I keep getting dry hits. maybe I'm using too small a coil.

    You got any wicking tips to share?

    Thanks
     
  7. trickywoo

    trickywoo Initiate

    Joined:
    May 10, 2015
    Messages:
    48
    Likes Received:
    49
    I'm keeping my wicks as short as possible so they just touch the holes in the deck and thinning them out a little bit. I haven't tried a coil smaller than 2.5mm but each of the coils I have tried at that size seems to work ok. Also keep an eye on the juice ports and tip the tank to release bubbles that seem to want to get caught there.

    Only other thing I can think of is checking that the juice port and the opening on the side are lined up properly.

    Hope something in there has helped!

    TW
     
    • Like Like x 1
  8. Major Hazzard

    Major Hazzard Achiever

    Joined:
    Jan 27, 2014
    Messages:
    1,361
    Likes Received:
    643
    Thanks... I'm thinking my wicks are too long.. I'll try some shorter ones.
     
  9. ji7800

    ji7800 Initiate

    Joined:
    Jan 31, 2017
    Messages:
    14
    Likes Received:
    1
    what ohm"s does it read out to?
     
  10. tony68

    tony68 Veteran

    Joined:
    Jul 9, 2016
    Messages:
    5,712
    Likes Received:
    5,801
    Ive had the same problem but now ive nailed it. Hard to explain but wick it up like you have been take a few puffs as soon as you think your getting dry hits or flavour probs open it up and carefully pull the ends of the wick out of the juice holes and trim off a couple of millimetres and drop the ends back in to the juice wells . Bit of a faff but seems to work for me.
     
  11. trickywoo

    trickywoo Initiate

    Joined:
    May 10, 2015
    Messages:
    48
    Likes Received:
    49
    It came out at 0.51ohms.
     

Share This Page