POTV - Your vaping community

Wanting to join the rest of our members? Why not sign up today!

Register

Need help with dual build

Discussion in 'Rebuildable Mods and Devices' started by Hokage, Dec 7, 2017.

  1. Hokage

    Hokage Member

    Joined:
    Dec 7, 2017
    Messages:
    9
    Likes Received:
    0
    What's up ? I just recently got CSMNT rda and I'm trying to build duel coil on there. I have a smok t priv kit also.
    Now the problem is when I put 2x (ud pre built specialty coils - ss316l staggered fused clapton 0.15ohm) and I also had to clip some out because it's a postless deck. the resistance said is too low it read about .05 normally I have a tank which is .15 so I figured if I put two coil I listed would work out. I can only use one coil on that deck to work but I really wanna use dual coil on my deck.
    Can you suggest me what duel coils I can use for my smok t priv plz? The name of the coil and which ohm I should get I want a safe ohm setting for my CSMNT RDA. Plz contact me back asap thank you
     
  2. haich

    haich Postman

    Joined:
    Apr 2, 2017
    Messages:
    546
    Likes Received:
    292
    is any of the coil touching anything else?
    have you tried removing one coil and seeing what the resistance is?
     
  3. DaveVapes

    DaveVapes Initiate

    Joined:
    May 18, 2017
    Messages:
    48
    Likes Received:
    17
    I suspect that when you install the coils, before they are dry burned and bedded in to work out the hotspots the current is following the path of lest resistance so your getting much lower ohms than you’re expecting. Too low for your device.
    I had a similar situation, my solution was to install one coil, bed it in and then install the second coil and bed that one in afterwards.
     
  4. stevoknevo

    stevoknevo Achiever

    Joined:
    Nov 28, 2014
    Messages:
    1,601
    Likes Received:
    890
    Two coils halves the total resistance so 0.15 divided by two = 0.075. It's reading lower as the hotspots need worked out but even then the resistance will be too low as most mods are 0.1 minimum.

    Contact smut on here and ask him to make you some of his aliens at 0.2 for a pair (0.4 per single coil) Until then you'll have to use your rda in single coil mode.
     
    • Like Like x 1
    • Thank Thank x 1
  5. Myashey

    Myashey Postman

    Joined:
    May 26, 2016
    Messages:
    524
    Likes Received:
    288
    When doing a dual build the result is halved, so two 0.15 coils will come out at 0.075, obviously there is a little give and take, hence the 0.05 reading. To get your device to 0.15 you need to be installing two 0.3 coils.
     
  6. DaveVapes

    DaveVapes Initiate

    Joined:
    May 18, 2017
    Messages:
    48
    Likes Received:
    17
    Doesn’t the T-Priv fire down to 0.06 in TC mode?
     
  7. Hokage

    Hokage Member

    Joined:
    Dec 7, 2017
    Messages:
    9
    Likes Received:
    0
    I did that which works btw thanks but how can I make a dual build on my deck ??
     
  8. Hokage

    Hokage Member

    Joined:
    Dec 7, 2017
    Messages:
    9
    Likes Received:
    0
    How can I contact him ? Another question does the resistance change if u clip off some part of the coil leg since I have to cuz it's a postless decided ?
     
  9. Hokage

    Hokage Member

    Joined:
    Dec 7, 2017
    Messages:
    9
    Likes Received:
    0
    Where can I get those ? N what's the difference kanthal and nicrhome n all that ? Which is the best material wire
     
  10. Hokage

    Hokage Member

    Joined:
    Dec 7, 2017
    Messages:
    9
    Likes Received:
    0
    Yes but idk how to use the tc mode sadly I stick with wattage mode
     

Share This Page