POTV - Your vaping community

Wanting to join the rest of our members? Why not sign up today!

Register

Trillium with Anyvape adaptor.

Discussion in 'Mouth to Lung Vaping' started by Coolie27, Dec 4, 2018.

  1. Coolie27

    Coolie27 Achiever

    Joined:
    Apr 19, 2017
    Messages:
    2,014
    Likes Received:
    1,427
    ‘Me juice tastes like me juice’ laughing
     
  2. Sprite71

    Sprite71 Postman

    Joined:
    Oct 25, 2017
    Messages:
    929
    Likes Received:
    950
    :D I’ve already been there!!

    I got this from the Eden Mods facebook page

    “Use an old coil, rip out the positive pin so it creates no resistance on the Trillium pin. Screw the coil in then wind it out again while applying pressure to one side.”

    I got it out, hope it’s not something that’s going to keep happening... or it will be back in the drawer.
     
    • Like Like x 1
    • Thank Thank x 1
  3. Simon G

    Simon G Legend

    Joined:
    Apr 12, 2016
    Messages:
    17,666
    Likes Received:
    16,879
    Thank you! I'll have a go later .... FFS, what a stupid design.
     
    • Like Like x 1
  4. Sprite71

    Sprite71 Postman

    Joined:
    Oct 25, 2017
    Messages:
    929
    Likes Received:
    950
    I know. I wasn’t bothered at first because I doubted I would be using it with any of the other types of coils BUT just putting a fresh nautilus coil in doesn’t work ... you get low ohms message. New coil wouldn’t work afterwards.
     
    • Like Like x 1
    • Thank Thank x 1
  5. 4Dee

    4Dee Postman

    Joined:
    Aug 18, 2018
    Messages:
    263
    Likes Received:
    407
    I had this stuck adpter problem and the suggestion on FB group didn't work for me. In the end I used some small pliers opened outwards against the inner threads of the adapter, and that gave me enough purchase to remove it without damaging threads.
     
    • Like Like x 2
  6. Coolie27

    Coolie27 Achiever

    Joined:
    Apr 19, 2017
    Messages:
    2,014
    Likes Received:
    1,427
    This worked for me so thanks for sharing. I just screwed the nautilus coil back in quite tight and gave a little bit of pressure to the left and it came out didn't take the pin out. Cheers
     
    • Like Like x 2
  7. eyeball kid

    eyeball kid Legend

    Joined:
    Mar 21, 2016
    Messages:
    13,822
    Likes Received:
    14,270
    Have I missed something here or is this thread just about buying adapters to turn the stock coil version of the rose v3 into a really hard to wick version of the Rose v3, lol.
     
    • LOL LOL x 3
    • Like Like x 1
  8. Simon G

    Simon G Legend

    Joined:
    Apr 12, 2016
    Messages:
    17,666
    Likes Received:
    16,879
    that's what it started out as ... now it's about turning a stock coil version of the rose 3 into an over priced nautilus. :D
     
    • LOL LOL x 4
    • Like Like x 1
  9. Coolie27

    Coolie27 Achiever

    Joined:
    Apr 19, 2017
    Messages:
    2,014
    Likes Received:
    1,427
    Lol- when you put it like that! it was very cheap on Ifancy one so I impulse bought it and thought I would consider the Rose v3 after testing this one. Is the Rose easy to wick and coil? I’ve watched a few vids, it looks a bit tricky
     
    • LOL LOL x 1
  10. eyeball kid

    eyeball kid Legend

    Joined:
    Mar 21, 2016
    Messages:
    13,822
    Likes Received:
    14,270
    Dead easy to wick and a world better than the rba system for aspire coils but still a fecking nuisance really. A bit like the dvarw. Once wicked your fine. But like the extra process of removing the chamber on the dvarw you have to pull the deck barrel from the bottom and fit a wicking crown. Sounds more complex than it is. Just a touch more work than say the berserker or hastur/true.
    Very good though. Used one pretty constantly until the slew of new tanks that arrived this year.
     
    • Like Like x 1

Share This Page