Sub-Ohm Warning!

Readers who are building very low ohm coils must be aware of the risks in regards to batteries and inhalation.
Please read THIS POST for more information.

POTV - Your vaping community

Wanting to join the rest of our members? Why not sign up today!

Register
  1. The POTV Charity Fundraising Event for 2019 is go! Check out the prizes and make your donations here.
    Dismiss Notice

Mesh/Strip RTA & Mesh/Strip Supplier (UK Based)?

Discussion in 'Cloud Chasing & Sub Ohming' started by richydraper, Feb 15, 2019.

  1. richydraper

    richydraper Postman

    Joined:
    May 23, 2016
    Messages:
    57
    Likes Received:
    13
    So every time i buy V8Baby Mesh Coils it HURTS in the pocket. looking for a replacement to my TV12 Baby Prince.

    looking for something rebuildable rather than using pre-built coils... ideally no wider than 26mm (else it will hang ove the edge of my mod) would like airflow to at least equal or exceed the baby prince.

    also if im gon start building again, any suggestions for mesh/strip suppliers?
     
  2. Lee

    Lee Vendor

    Joined:
    Jan 1, 2015
    Messages:
    11,171
    Likes Received:
    13,114
    Wotofo profile RDA is mesh, rebuildable and a great RDA. Worth a look
     
    • Like Like x 2
  3. nwhornet

    nwhornet Veteran

    Joined:
    Feb 22, 2016
    Messages:
    6,059
    Likes Received:
    5,068
    Wotofo or Nexmesh strips are made specifically for the Profile & take the guesswork out of building. Plenty of UK vendors stock the RDA & mesh. Vaping101 is a good place to start as last time I looked they had them & both meshes in stock.
     
  4. kamido

    kamido Achiever

    Joined:
    Jun 15, 2016
    Messages:
    3,252
    Likes Received:
    3,632
    I asked the same question about a mesh RDA and some helpful apes pointed me towards the wotofo profile it’s the only mesh RDA I have but it’s a cracker not to expensive and simple to build on well thorth a buy :2thumbsup:
     
  5. richydraper

    richydraper Postman

    Joined:
    May 23, 2016
    Messages:
    57
    Likes Received:
    13
    Nice one @Lee, I've seen them but theyre not really my thing... I'd prefer an RTA rather than RDA as it suits my life a little better.

    @nwhornet thanks ill make sure to check them out :)
     
  6. nwhornet

    nwhornet Veteran

    Joined:
    Feb 22, 2016
    Messages:
    6,059
    Likes Received:
    5,068
    Can't think of a rebuildable mesh tank using something like the Profile mesh (or any other type). Closest would be a genesis style RDTA with mesh wicks.
     
  7. richydraper

    richydraper Postman

    Joined:
    May 23, 2016
    Messages:
    57
    Likes Received:
    13
    may have to carry on with my TFV12 for now then, even with its expensive coils

    thanks all for the replies
     
  8. nwhornet

    nwhornet Veteran

    Joined:
    Feb 22, 2016
    Messages:
    6,059
    Likes Received:
    5,068
    Stick a Profile on a squonker, match made in heaven :)2.
     
  9. Mordacai

    Mordacai Postman

    Joined:
    Feb 15, 2019
    Messages:
    196
    Likes Received:
    84
    richydraper, may have some ideas for you.

    Digiflavor Themis 25mm RTA, has a mesh deck as well as a coil deck. Just check version if buying.

    Vandy Vape Mesh 24 RTA, only slight issue is the slide to fill system. Could end up emptying the tank in your pocket.

    And a UK mesh supplier, themeshcompany.com. They also sell through Amazon.

    And I have no experience with mesh RTA's, but I do read. A lot.
     
  10. MavicP

    MavicP Postman

    Joined:
    Oct 4, 2018
    Messages:
    620
    Likes Received:
    778
    I have a Themis Mesh, great flavour from it but I find that it can be inconsistent. It's easy to build on, but I've tried a few different wicks to see which works best. Muji - not so good, Cotton Bacon Prime - pretty good, best so far, Cotton Gods is the next build.
    When it's going well the flavour blows everything else out of the water.
     
    • Like Like x 1

Share This Page